[email protected]

AASHTO M 270M/M 270 - Standard Specification for

Standard Specification for Structural Steel for Bridges This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. ASTM B209 - 14 - Standard Specification for Aluminum and 1.1 This specification 2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys ( Note 1) and tempers shown in Tables 2 and 3, and in the following finishes:(A) Limits are in weight percent maximum unless shown as a range or stated otherwise.

ASTM B209 Aluminum Sheet and Plate asme sb 209 alloy

ASTM B209 specification covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 3, and in the following finishes:(A) Limits are in weight percent maximum unless shown as a range or stated otherwise. (B) Analysis shall be made for the elements for which limits are shown in this table. ASTM B209-14 Red - Standard Specification for Aluminum 1.1 This specification 2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 3, and in the following finishes:(A) Limits are in weight percent maximum unless shown as a range or stated otherwise. ASTM B432-19 - Standard Specification for Copper and Standard Specification for Copper and Copper Alloy Clad Steel Plate. 1.1 This specification establishes the requirements for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of copper or copper-base alloy. The material is generally intended for pressure vessel use but

ASTM-B-209-96

I.8 standard two-sides brightfinisl:sheet sheet having a uniform bright finish on both sides. 3.1.9 platea rolled product that is tectangular in cross section with thickness not less than 0.250 in., and with shcared or sawed edges. 3.1.10 alclad platecomposite plate compriscd of an aluminum-alloy core having on both surfaces (if on onc side Annual Book Slandards. ASTM-B171 Standard Specification for Copper-Alloy Plate This specification establishes the requirements for plates, sheets, and circles cut from plates and sheets made of UNS C36500, C44300, C44400, C44500, C46400, C46500, C61300, C61400, C63000, C63200, C70600, C70620, C71500, C71520, or C72200 copper alloy. These materials are recommended for use in pressure vessels, condensers, and heat exchangers. BS EN 485-1:2016 - SIGMA ALUMINUMwrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing. It applies to products with a thickness over 0,20 mm up to and including 400 mm. For many special applications of aluminium strip, sheet and plate, specific European Standards

Plate and Sheet Flatness - Rolled Alloys, Inc.

The requirements on the flatness of the plate and sheet products sold by Rolled Alloys vary considerably by the type of product, by alloy, by thickness and by the size of the piece. AMS and ASTM standards exist which cover the flatness requirements for most plate and sheet items as produced by the mill. Specifications A 480 and AMS 2242 cover Standard Specification for Aluminum and Aluminum-Alloy Note 1 - Throughout this specification, use of the term alloyin the general sense includes aluminum as well as aluminum alloy. Note 2 - See Specification B 632/B 632M for tread plate. Note 3 - See Specification B 928/B 928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Standard Specification for Aluminum and Aluminum-Alloy Note 1-Throughout this specification, use of the term alloyin the general sense includes aluminum as well as aluminum alloy. Note 2-See Specification B 632/B 632M for tread plate. Note 3-See Specification B 928/B 928M for marine sheet and plate.

Standards - ASTM Standards - High Strength Plates

ASTM A588. "Standard Specification for High Strength Low-Alloy Structural Steel With 50,000 psi (345 MPa) Minimum Yield Point". This standard covers high strength low-alloy structural steel shapes, plates and bars for use in riveted, bolted or welded construction with minimum yield point strengths of Standard Specication for Aluminum and Aluminum Alloy Products 2.3 ISO Standards:4 ISO209-1 Wrought Aluminum and Aluminum Alloys-Chemical Composition and Forms of Product ISO2107 Aluminum, Magnesium and their Alloys-Temper Designation ISO6361-2 Wrought Aluminum and Aluminum Alloys, Sheets, Strips, and Plates 2.4 ANSI Standards:5 H35.1/H35.1(M) Alloy andTemper Designation Systems for Aluminum