[email protected]

Carbon Steel reactive

Grade S355 J2. 6000mm long x 3-100mm THK . 15mm - 600mm wide . HIGH YIELD SQUARE BAR . Grade S355 J2. 6000mm long x 8mm - 300mm . HIGH YIELD EQUAL ANGLES . Grade S355 J2. 20 x 20 x 3mm - 300 x 300 x 40mm . HIGH YIELD UNEQUAL ANGLES . Grade S355 J2. 30 x 20 x 3mm - 250 x 90 x 16mm . HIGH YIELD ROUND BAR . Grade S355 J2 . 6000mm long x 10mm EN 10025-2 S355J2G3 high strength structural steel plate S355J2G3 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. With its low carbon equivalent, it possesses good cold-forming properties. The plate is produced by fully killed steel process and supplied in normalized or controlled rolling condition. S355J2G3 Application

S355 / S355J2 Low Carbon Manganese Steel Hillfoot

S355 grade steel is a medium tensile, low carbon manganese steel which is readily weldable and possesses good impact resistance (also in sub-zero temperatures). This material is commonly supplied in the untreated or normalised condition and is available in several variations (denoted by additional letters and/or digits) which offer slight S355 Structural Steel SupplierJan 30, 2017 · S355JR, S355AR & S355J2/K2+N. S355 a structural grade steel with a minimum yield strength of 355 N/mm². Commonly used in the engineering and construction industry, S355 offers high yield and tensile strength and is supplied with a variety of treatments and test options making it a highly usable steel in your construction project. S355J2+NS355J2+N Steel Plates355J2+N Structural Steel S355J2+N is the most common high strength steel for construction that we sell. It is a non-alloy structural steel to EN10025-2 2004. With its increase yield strength of S355 MPa over other construction steels such as S275 and S235 it is an excellent choice for delivering

SPECIFICATION COMPARISON (PLATE) - Quantum Steel

Gr 43D 300 WDD * S275 J2 G3 S275 J2 + N Gr 50B 350 WA S355 JR S355 JR + AR Gr 50C 350 WC S355 JO S355 JO Gr 50D 350 WDD S355 J2 G3 S355 N * NOT A DIRECT EQUIVALENT ** REPLACES PREVIOUS SPECIFICATIONS. BS 4360, SANS 1431 AND EN 10025. 011 824 1694 [email protected] quantumsteel.za GUIDE TO COMMERCIALLY AVAILABLE STEEL Structural Pantech GroupEN10025 S355 JR:355:470 630 27:EN10025 5355 JO:0:27:EN10025 S355 J2-20:27:Equal Angle Bar:EN 10025 S275 JR:275:410 560 3x20x2Omm to 20x200x200mm:6m, 9m & 12m:Unequal Angle Bar:JIS G3101 SS 400:235:410 510 6x75x50mm to 12x200x100mm:Flat Bar:EN 10025 S275 JR:275:410 560 3x25mm to Structural Steel - BS EN 10025 S355 and S275S355, S355JR, S355J2, S355J2+N steel in plate, round bar, flat bar and blocks. S355 steel is a low carbon steel whose specifications offer high yield strength. The average minimum yield for S355 steel is 355 N/mm² giving its name:S355. BS EN 10025 S275 & S275JR supercedes BS4360 43A and 43B. S355 sheet/plate can also be flame cut to a profile

Structural Steel Plate - S355 J2 +N & S355 K2 +N

S355 Steel Plate Stock. German made (normally Dillinger, Thyssen or Clabecq with some exceptions) with 3.2 certification to EN10204. tested to -40 C on a per heat basis ( S355 J2+N) or -40 C on a per plate basis ( S355 K2+N) Thickness 6 300mm. Width 1.5m, 2m, 2.5m and 3m. Length 6m and 12m. Structural Steel Sub-Grades JR, J0 & J2 Does It Matter?S275 JR 0 S355 JR 3 % S275 J0 3.5 % S355 J0 4 % S275 J2 4 % S355 J2 10 % In very general terms, JR steel material is most readily available from stock and mill. It is also the lowest priced sub-grade and so for maximum economy and availability, JR quality material should be used whenever possible. Higher quality materials, J0 Structural steel grade designations according to EN J2 indicates that the Impact Test was performed to 27 joules minimum at 20°C. K2 indicates that the Impact Test was performed to 40 joules minimum at 20°C. G3 indicates delivery conditions are at the manufacturers discretion. The last letter, if applicable:H indicates Hollow Section.

S355J2/S355J2+N/S355J2G3 - Waldun Steel

S355J2/S355J2+N/S355J2G3. S355J2 steel is a carbon manganese ,high yield non alloy steel. It is called S355 because of the average minimum yield for this material is 355 Mpa.As a structural steel,it has excellent strength and weldability.It can be readily welded to other weldable steel.